almost_fast@yahoo.com
12-31-1969, 08:00 PM
On May 16, 11:31*am, "Doug McLaren" <dougmc
+usenet-20080...@frenzied.us> wrote:
> I recently picked up a Trek 2000 Alpha SL bike used, and I've been
> fixing it up. *I don't know the year, but from what I was told I'm
> guessing late 1990s.
>
> It's got Shimano RSX components.
>
> So, the first thing broken was the left/front shifter (it's a three
> speed brifter.) *Would shift up but not down. *Cleaned it up with
> WD-40 and it did start working, though it sounds like there's still
> grit in there.
>
> However, it could barely shift the gear -- I have to really crank down
> on it. *The right shifter/rear derailleur is much easier. *The
> derailleur itself seems fine, the cables are fine (and the routing is
> correct), so I found a replacement brifter, and put it in. *Same
> problem.
>
> Upon closer investigation, to move the front derailleur from the
> loosest position by pulling the cable manually away from the frame
> between the two braze-ons on the bottom tube requires a lot more
> effort than my other bike.
>
> Removing the derailleur, it seems fine, but it requires a _lot_ of
> effort to move it. *It's not stuck -- it slides freely, and it
> requires just as much effort to `compress' it as it does to keep it
> from uncompressing. *It's like they put a big honking spring in there,
> far larger than I'd think was needed. *I've certainly never heard of a
> spring failing in such a way to *increase* the tension, so I'm quite
> confused by this -- it's like it was designed this way, but it just
> doesn't seem right.
>
> To be fair, I don't have a lot of experience fixing bikes -- I sort of
> know what I'm doing, and have books to refer to, but don't have the
> experience to tell me what sort of tension to expect here -- but it
> seems way too high, like 2-3x as high as it ought to be.
>
> Looks like it's a FD-A417 Chainstay angle 63-66 degrees. *Looking
> carefully at the spring while it's moved, it looks like the entire
> spring is working and is clean and not rusted and such.
>
> Thoughts?
>
> --
> Doug McLaren, dou...@frenzied.us
> `The chief obstacle to the progress of the human race is the human race.'
> *- Don Marquis.
Shifting front STI is often harder than rears. That said, they're can
be really hard if the cable's under the tab (by the pinch bolt)
instead of over it. Not enough leverage. Check and maybe move the
cable so it passes by the tab on the "inboard" side (of the bicycle)
then over the top of the pinch bolt.
+usenet-20080...@frenzied.us> wrote:
> I recently picked up a Trek 2000 Alpha SL bike used, and I've been
> fixing it up. *I don't know the year, but from what I was told I'm
> guessing late 1990s.
>
> It's got Shimano RSX components.
>
> So, the first thing broken was the left/front shifter (it's a three
> speed brifter.) *Would shift up but not down. *Cleaned it up with
> WD-40 and it did start working, though it sounds like there's still
> grit in there.
>
> However, it could barely shift the gear -- I have to really crank down
> on it. *The right shifter/rear derailleur is much easier. *The
> derailleur itself seems fine, the cables are fine (and the routing is
> correct), so I found a replacement brifter, and put it in. *Same
> problem.
>
> Upon closer investigation, to move the front derailleur from the
> loosest position by pulling the cable manually away from the frame
> between the two braze-ons on the bottom tube requires a lot more
> effort than my other bike.
>
> Removing the derailleur, it seems fine, but it requires a _lot_ of
> effort to move it. *It's not stuck -- it slides freely, and it
> requires just as much effort to `compress' it as it does to keep it
> from uncompressing. *It's like they put a big honking spring in there,
> far larger than I'd think was needed. *I've certainly never heard of a
> spring failing in such a way to *increase* the tension, so I'm quite
> confused by this -- it's like it was designed this way, but it just
> doesn't seem right.
>
> To be fair, I don't have a lot of experience fixing bikes -- I sort of
> know what I'm doing, and have books to refer to, but don't have the
> experience to tell me what sort of tension to expect here -- but it
> seems way too high, like 2-3x as high as it ought to be.
>
> Looks like it's a FD-A417 Chainstay angle 63-66 degrees. *Looking
> carefully at the spring while it's moved, it looks like the entire
> spring is working and is clean and not rusted and such.
>
> Thoughts?
>
> --
> Doug McLaren, dou...@frenzied.us
> `The chief obstacle to the progress of the human race is the human race.'
> *- Don Marquis.
Shifting front STI is often harder than rears. That said, they're can
be really hard if the cable's under the tab (by the pinch bolt)
instead of over it. Not enough leverage. Check and maybe move the
cable so it passes by the tab on the "inboard" side (of the bicycle)
then over the top of the pinch bolt.